If your roof is leaking or looking tired, you have three real options: repair the problem area, lay a new layer of shingles over the old one, or tear everything off down to the deck and start fresh. The right answer depends on the age of the roof, how many layers are already up there, and what the decking underneath looks like. Before you pick any of them, take the time to vet the roofing contractors you invite to bid, because the quality of the install matters as much as the material.
Start With What the Roof Is Telling You
Most homeowners first notice a roof problem from inside the house: a stain on the ceiling, a damp spot in the attic, or a musty smell after the first big rain of the season. From the ground, look for curled or cracked shingles, bare patches where the granules have washed away, sagging lines along the ridge, and loose flashing around chimneys, vents and skylights.
A few questions help sort out how serious it is:
- How old is the roof? If you don’t know, check your home purchase paperwork or ask the city whether a reroof permit is on file for your address.
- Is the damage in one spot or spread across several slopes?
- Have you had leaks before, and were they in the same place?
- Does the attic show daylight, dark staining on the wood, or soft spots?
A single leak on an otherwise healthy roof points toward repair. Widespread wear on an older roof points toward replacement.
Option 1: Repair
A repair fixes a specific failure, such as a few blown-off shingles, a cracked pipe boot, or flashing that has pulled away from a wall. It is the fastest and least disruptive choice.
Repair makes sense when:
- The roof is well within its expected life for the material.
- The damage is limited to a small area.
- The decking underneath is solid.
The catch is matching. Older shingles fade, so a patch may not blend in perfectly. And if the roof is near the end of its life, a repair can turn into the first of several service calls in a short stretch. Ask the contractor to tell you honestly whether they think the rest of the roof has a few good years left.
Option 2: Overlay Reroof
An overlay, sometimes called a layover or roof-over, means installing new shingles directly on top of the existing layer without removing it. It skips the tear-off labor and the disposal, so it often costs less and finishes sooner than a full replacement.
It also comes with real limits:
- Building codes generally cap how many layers a roof can have. If you already have two layers, an overlay is usually off the table. Your contractor and the city building division can confirm what applies to your home.
- Nobody gets to inspect the deck. Rot, soft spots or old damage stay hidden under the new layer.
- The extra weight adds load to the roof framing.
- Some shingle manufacturers limit or change warranty coverage on overlays, so read the warranty terms before you agree.
- New shingles laid over uneven old ones can show ripples and wear faster.
An overlay can be a reasonable choice for a single-layer roof with a sound deck when you plan to sell in the near future or need to stretch a budget. It is less appealing if you plan to stay in the house for a long time.
Option 3: Full Tear-Off
A tear-off removes every existing layer down to the roof deck. The crew can then replace damaged sheathing, install fresh underlayment, and redo flashing and ventilation from scratch.
Tear-off is usually the better path when:
- There are already two or more layers.
- You have recurring leaks or signs of deck damage.
- You want the strongest available warranty and the longest service life.
- You plan to stay in the home for many years.
It costs more and takes longer, and you should expect noise and debris for a few days. Ask how the crew will protect landscaping, gutters, and anything stored in the attic or garage.
For reroofing in Union City, a building permit is typically required whether you choose an overlay or a tear-off. California’s energy code, Title 24, includes cool roof requirements for some reroofing projects, but whether they apply depends on your climate zone and roof type. In the milder Bay Area climate zones, they often don’t apply to sloped home roofs. Ask your contractor whether they apply to your house and confirm with the City of Union City Building Division.
How to Vet Roofing Contractors in Union City
Get at least two or three written bids, and use the same checklist for each one. Whichever roofing contractors in Union City you invite to bid, you should be able to verify every item below before signing anything.
1. Check the license. In California, contractors doing work above a small dollar threshold must be licensed by the Contractors State License Board. You can look up any license on the board’s website. Confirm the license is active, the business name matches the bid, and the license includes the C-39 Roofing classification, or another classification that legally covers the work.
2. Confirm workers’ compensation coverage. The license lookup shows whether the contractor has workers’ comp on file or has claimed an exemption. A roofing company with employees on your roof should carry it.
3. Ask for proof of liability insurance. Request a certificate of insurance and check that it is current.
4. Make sure the permit gets pulled. The contractor should pull the permit and schedule inspections. Be cautious if anyone suggests skipping the permit to save time or money.
5. Get a detailed written scope. A good bid spells out:
- Repair, overlay, or tear-off
- The shingle or roofing product, by manufacturer and line
- Underlayment, flashing, drip edge and ventilation work
- How damaged decking will be handled and priced
- Cleanup, debris removal and nail sweeping
- Start date, estimated duration and payment schedule
6. Understand the warranty. There are usually two separate warranties:
- Manufacturer warranty: covers defects in the roofing material itself. Some manufacturers offer extended coverage only when a certified installer follows their full system.
- Workmanship warranty: covers installation errors and comes from the contractor. Length and terms vary widely, so get it in writing.
Ask who you would call if a leak shows up in year three, and what that call would cost you.
If you are comparing bids now, it helps to talk with a local crew that handles roof repair and replacement in Union City and can explain which of the three options fits your roof.
A Simple Way to Decide
If you are still unsure, line up your situation against these quick rules of thumb:
- One small problem, younger roof, solid deck: repair.
- One existing layer, sound deck, shorter time in the home: an overlay may be worth pricing.
- Two layers already, repeated leaks, soft spots, or a long stay ahead: full tear-off.
Ask each contractor to explain why they recommend one option over another. A trustworthy roofer will walk you through the tradeoffs instead of pushing the biggest job.
FAQ
Do I need a permit to reroof in Union City? Reroofing work generally requires a permit. Check with the City of Union City Building Division for current requirements, and expect your contractor to handle the application.
Can a contractor tell if my deck is damaged before the tear-off? They can spot clues from the attic and from soft areas underfoot, but the full picture usually appears only once the old roofing comes off. That’s why a good bid explains how deck repairs will be priced.
Is an overlay always cheaper in the long run? Not necessarily. It saves on labor up front, but hidden deck problems, possible warranty limits and a shorter service life can offset those savings.

